Download the Windows 10 ISOWhen setup completes this installation phase, your PC will restart. Figure 2: the Volumes tab, set to boot from CD imageTo overcome this, we will need to use a tool, Wimlib, which is able to split this file in two parts. Figure 1: the Volumes tab, set to boot from a real CD. Mount drives: shows the host drives that will be available through the My Computer icon on the desktop. FAT32 has a file size limit of 4GB while the installation ISO now contains one file that is larger.Enable My Computer icon on your Mac desktop (external file system): when checked, SheepShaver gives access to host drives.Iso file on your Mac: Prepare the USB driveWhile the ISO is downloading, we can prepare our USB drive. For details about configuring network boot on.Choose for Windows 10, then select the preferred language, go for the “64-bit Download” and wait for the download to complete to get the. When you open this link on macOS, it should show you the ability to download the ISO rather than the Media Creation tool, which is shown when opening the same on a Windows-based PC.The procedures in this chapter describe setting up a network boot server on a Red Hat Enterprise Linux 7 system. Boot from AOMEI Linux System applies to older or Linux based computers, and the third one Boot from custom image file allows you to load the special micro-system created by AOMEI PE Builder or Bart PE.Let’s start by downloading the ISO from Microsoft. Select AOMEI Windows PE System and click Start Service.It will directly create a Windows PE system image for network boot. The installer will stay on the Getting Ready.2.Copy all smaller files to the USB driveAfter the previous step, our USB drive is prepared. Finally click “Erase” to complete the process. In the dialog, enter a name for the drive (WINUSB here), choose to format as “MS-DOS (FAT)” and “Master Boot Record” as scheme. Insert the drive in your Mac and start Disk Utility.In Disk Utility, choose to show all devices:Then, on the left side, select your USB drive from the list and click Erase on the top left menu.
![]() As is instructed on the Brew website, copy and paste the mentioned line in a terminal and execute it. The easiest way to get this installed on your Mac is by using Brew ().So, as just mentioned, we start by installing Brew. This is a tool that is developed to work with, and modify. Unfortunately we have to work around that by splitting the file in two parts, smaller than the limit of our file system on the USB drive.To accomplish this, we can use Wimlib (). As you can see, the sources folder contains one large file: install.wim which is over 4GB and will not fit on the FAT32-formatted USB drive:We will take care of that later so for now, copy all remaining files to the USB drive using Finder.I typically start by copying all separate files and folders, except for the sources folder:Then I create the sources folder and copy all files from sources with the exception of install.wim: Prepare to split install.wimSo far things were pretty straightforward and if it wouldn’t be for that large file it would be a piece of cake. What internet explorer for mac“/Volumes/WINUSB/sources/install.swm” the destination of where the split files should end. Just do ls /Volumes from the terminal to see what is there. Keep in mind that the name under /Volumes depends on the ISO name so you need to adjust this accordingly. “/Volumes/CCCOMA_X64FRE_EN-GB_DV9/sources/install.wim” which is the source file to split. “split” to indicate that we want to split this larger file In the same or a new Terminal session, execute the following: ~ % wimlib-imagex split /Volumes/CCCOMA_X64FRE_EN-GB_DV9/sources/install.wim /Volumes/WINUSB/sources/install.swm 4000Splitting WIM: 4654 MiB of 4654 MiB (100%) written, part 2 of 2Finished splitting "/Volumes/CCCOMA_X64FRE_EN-GB_DV9/sources/install.wim"In the command above, we told to execute the wimlib-imagex tool (part of Wimlib) and passed some arguments: Create Network Boot From Windows Drivers For Your(Optionally) download Windows 10 drivers for your MacIf you plan to use the USB drive, which you created with the above steps, on a regular PC then you can skip this step. Size of the destination file, so the file will be split in a part of 4000MB and the rest.After this command completes, you can see that now two files were created on the USB drive:The Windows 10 installer knows how to deal with these and will just work fine.That should be all you need to create a bootable USB drive for Windows 10 installation. Adjust this as well when you chose something different earlier. If you want to download the required drivers for another model, you can simply pass it using the –model parameter. /brigadierAs you can see in the output, executing brigadier automatically detected the model identifier of the mac which we executed this on. /brigadier: ~ % cd brigadier-master %. Brigadier, which is basically a script, works just from macOS directly as well.From the author’s Github page: , click the green Code button then choose to “Download ZIP”Once the file is downloaded, open a fresh Terminal session and navigate to the “brigadier-master” in your Downloads folder, then simply execute it using. As I did from Windows in a previous article, I will use Brigadier for this. Boot from the USB driveAs the final step, now that the USB drive is prepared, with or without additional drivers for your Mac, you can boot from it.On a regular PC, this is usually done by pressing a key at BIOS time to bring up a boot menu (F11 is often used for this) or, for some older BIOS, by changing the boot order from the BIOS setup.
0 Comments
Leave a Reply. |
AuthorRandi ArchivesCategories |